View MN102L62G_991734.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MN102L62G
Type ROM (x8-bit / x 16-bit) x RAM (x 8-bit / x 16-bit) x Package Minimum Instruction Execution Time Interrupts
MN102L62G 128 K 5K LQFP100-P-1414 *Lead-free 100 ns (at 4.5 V to 5.5 V, 20 MHz) * RESET * Watchdog * Timer counter 0 to 5 * Timer counter 6 to 7 * Timer counter 6 to 7 compare capture A * Timer counter 6 to 7 compare capture B * ATC transfer finish * External 0 to 4 * Serial ch.0, 1 transmission * Serial ch.0, 1 reception * NMI pin * A/D conversion finish Timer counter 0 : 8-bit x 1 (timer output, event count) Clock source ********************* 1/1, 1/128 of system clock frequency; 1/4 of low speed clock frequency; external clock Interrupt source **************** underflow of timer counter 0 Timer counter 1 : 8-bit x 1 (timer output, event count, A/D conversion start up) Clock source ********************* system clock; 1/4 of low speed clock frequency; external clock; timer counter 0 output Interrupt source **************** underflow of timer counter 1 Timer counter 2 to 3 : 8-bit x 1 (timer output, event count, UART baud rate generator) Clock source ********************* system clock; external clock; timer counter 0 output; timer counter 1, 2 output Interrupt source **************** underflow of timer counter 2, 3 Timer counter 4, 5 : 8-bit x 1 (timer output, event count) Clock source ********************* 1/4 of low speed clock frequency; external clock; timer counter 0 output; timer counter 3, 4 output Interrupt source **************** underflow of timer counter 4, 5 Timer counter 6, 7 : 16-bit x 1 (timer output, event count, input capture, output compare, PWM output, 2-phase encoder input) Clock source ********************* system clock; external clock; timer counter 4, 5 output Interrupt source **************** coincidence with compare capture A or at capture; coincidence with compare capture B or at capture; underflow of timer counter 6, 7 Connectable timer counter 0 to 5
Timer Counter
Serial Interface
Serial 0 : 7, 8-bit x 1 (common use with UART, transfer direction of MSB/LSB selectable) Clock source ********************* 1/16 of timer counter 2 frequency; 1/16 of timer counter 3 frequency; external clock; 1/2 of timer counter 2 frequency Serial 1 : 7, 8-bit x 1 (common use with UART, transfer direction of MSB/LSB selectable) Clock source ********************* 1/16 of timer counter 2 frequency; 1/16 of timer counter 3 frequency; external clock; 1/2 of timer counter 3 frequency UART x 2 (common use with serial 0, 1) I2C x 2 (single master)
I/O Pins A/D Inputs PWM Notes
I/O
80
* Common use : 16 (by 8 bits), 8 (by 4 bits), 56 (by bit)
8-bit x 8-ch. (with S/H) 16-bit x 2-ch. Burst ROM inferface support, ATC (between serial 0ch and internal RAM) support
1
MAE00002DEM
MN102L62G
Electric Characteriatics
Supply current
Limit Parameter Symbol Condition min Operating supply current VI = VDD or VSS, output open IDDopr f = 20 MHz , VDD = 5.0 V Pin with pull-up resistor is open Supply current at STOP IDDS all other input pins and Hi-Z state input/output pins are simultaneously applied VDD or VSS level Supply current at HALT IDDH f = 20 MHz , VDD = 5.0 V, output open (Ta = -40C to +85C , VDD = 5.0 V , VSS = 0 V) 30 mA 50 A 75 mA typ max Unit
Pin Assignment
TM7IOA,P91 TM6IOA,P86 TM7IOB,P92 TM6IOB,P87 TM5IO,P85
53
TM4IO,P84
52
100 98 96 94 92 90 88 86 84 82 80 78 76 99 97 95 93 91 89 87 85 83 81 79 77 75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
48
PA2, IRQ2 PA3, IRQ3 PA4, IRQ4 PA5,ADSEP RST VDD P00,D00,AD00 P01,D01,AD01 P02,D02,AD02 P03,D03,AD03 P04,D04,AD04 P05,D05,AD05 P06,D06,AD06 P07,D07,AD07 VSS P10,D08,AD08 P11,D09,AD09 P12,D10,AD10 P13,D11,AD11 P14,D12,AD12 P15,D13,AD13 P16,D14,AD14 P17,D15,AD15
49
PA1, IRQ1
50
PA0, IRQ0
51
TM3IO,P83
TM7IC,P93
TM6IC,P90
SBO1,P75
SBO0,P72
SBT1,P73
SBT0,P70
SBI1,P74
SBI0,P71
AN3,P97
AN2,P96
AN1,P95
AN0,P94
VDD
VDD
NMI
VSS
TM2IO,P82 TM1IO,P81 TM0IO,P80 A23,WDOUT,AN7,P47 A22,STOP,AN6,P46 A21,AN5,P45 A20,AN4,P44 VSS A19,P43 A18,P42 A17,P41 A16,P40 A15,P37 A14,P36 A13,P35 A12,P34 VDD A11,P33 A10,P32 A09,P31 A08,P30 A07,P27 A06,P26 A05,P25 A04,P24
MN102L62G
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
P60,WAIT
P56,ALE, ALE, BSTRE
VDD
SYSCLK
VSS
XI
XO
VDD
OSCI
P61,RE
P62, WEL
P63, WEH
P50, CS0
P51, CS1
P52, CS2
P53, CS3
P54, BREQ
P55, BRACK
P57, WORD
P20,A00
P21,A01
P22,A02
P23,A03
LQFP100-P-1414 *Lead-free
MODE
OSCO
25
1
2
3
4
5
6
7
8
9
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
See the next page for support tool.
MAE00002DEM
2
Support Tool
In-circuit Emulator EPROM Built-in Type
PX-ICE102L00 + PX-PRB102L25-LQFP100-P-1414 Type ROM (x 8-bit / x 16-bit) RAM (x 8-bit / x 16-bit) Minimum instruction execution time Package MN102LP25G 128 K 5K 100 ns (4.5 V to 5.5 V , 20 MHz) LQFP100-P-1414 *Lead-free MN102LF25Z 128 K 3K 100 ns (4.5 V to 5.5 V , 20 MHz) LQFP100-P-1414 *Lead-free
Flash Memory Built-in Type
Type ROM (x 8-bit / x 16-bit) RAM (x 8-bit / x 16-bit) Minimum instruction execution time Package
3
MAE00002DEM
MN102L62G
MAE00002DEM
4
Request for your special attention and precautions in using the technical information and semiconductors described in this material
(1) An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. (2) The technical information described in this material is limited to showing representative characteristics and applied circuits examples of the products. It neither warrants non-infringement of intellectual property right or any other rights owned by our company or a third party, nor grants any license. (3) We are not liable for the infringement of rights owned by a third party arising out of the use of the product or technologies as described in this material. (4) The products described in this material are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: * Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. * Any applications other than the standard applications intended. (5) The products and product specifications described in this material are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (6) When designing your equipment, comply with the guaranteed values, in particular those of maximum rating, the range of operating power supply voltage, and heat radiation characteristics. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (7) When using products for which damp-proof packing is required, observe the conditions (including shelf life and amount of time let standing of unsealed items) agreed upon when specification sheets are individually exchanged. (8) This material may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd.
2002 JUL

▲Up To Search▲

Price & Availability of MN102L62G

	To Download MN102L62G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .